View SC615_1163742.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

POWER MANAGEMENT Description
The SC615 is a high-current charge pump designed specifically for use with white LEDs used in camera flash applications. Only two small bucket capacitors are required to develop the output drive, providing a low EMI solution compared to inductive boost regulators. The SC615 has two modes of operation: Flash mode and Spotlight mode. The SC615 is capable of delivering 500mA of peak current for a duration of 500ms in Flash mode. In Spotlight mode the SC615 outputs 100mA and can remain enabled continuously. A minimum 0.5 sense resistor is used to set the current through the LED in both modes. This resistor dissipates up to 0.125W, reducing the power dissipation requirement of the SC615. The flash input (FLASH) overrides the control input (CTRL) to make sure the flash function is activated when called for. The thermally efficient MLPD-10 package and ceramic bypass and bucket capacitors help make the SC615 a high output current driver that requires a minimal amount of PCB area.
Charge Pump Flash LED Driver
Features
500mA Output Current - Flash Mode 3.0V to 5.25V Input Range Two Selectable Modes - Flash and Spotlight External Flash Control Pin for Synchronization to a Camera Module or Graphics Controller Spotlight Mode Current Setting - 100mA Short Circuit, Over-Voltage, and Over-Temperature Protection Soft-Start Functionality Two Control Inputs for Maximum Versatility Shutdown Current < 2A Micro Lead-frame Package MLPD-10, 3mm x 3mm
SC615
Applications
Mobile Camera Phones Digital Cameras PDAs with Built-in Cameras Multi-LED Backlit LCDs
Application Circuit
1
SC615
VIN C1+ C1C2+ C2VOUT GND ISET CTRL FLASH
9
3.0V to 5.25V
10F 1F
white LED
3 6 7 5
8 4 10
1F
1F
2
0.5
FLASH CTRL
July 11, 2005
1
www.semtech.com
SC615
POWER MANAGEMENT Absolute Maximum Ratings
Exceeding the specifications below may result in permanent damage to the device or device malfunction. Operation outside of the parameters specified in the Electrical Characteristics section is not implied.
Parameter Supply Voltage Output Voltage Pin Voltage - FLASH, CTRL, ISET, C1-, C2Pin Voltage - C1+, C2+ VOUT Short Circuit Duration Thermal Resistance, Junction to Ambient (JESD51 Standard Method)(1) Operating Ambient Temperature Range Junction Temperature Range Storage Temperature Range IR Reflow Temperature ESD Protection Level(2)
Symbol VIN VOUT
Maximum -0.3 to 6.5 -0.3 to 6.5 -0.3 to VIN + 0.3 -0.3 to VOUT + 0.3
Units V V V V
SC JA TA TJC TSTG TLEAD V ESD
Indefinite 49 -40 to +85 -40 to +150 -65 to +150 260 2 C/W C C C C kV
Notes: 1) Calculated from package in still air, mounted to 3"x 4.5", 4 layer FR4 PCB with thermal vias under the exposed pad per JESD51 standards. 2) Tested according to JEDEC standard JESD22-A114-B
Electrical Characteristics
Unless otherwise specified: TA = 25C for TYP, -40C to +60C for MIN and MAX; CBUCKET = COUT = 1.0F (ESR < 0.1); CIN = 10.0F; VIN = 3.0V to 5.25V; RISET = 0.5 (0.1%).
Parameter
Symbol
Conditions FLASH high, RISET = 0.5 3.3V < VIN < 4.2V 2.8V < VOUT < 4.25V FLASH low, RISET = 0.5 CTRL high, 2.8V < VOUT < 4.5V 3.0V < VIN < 4.5V FLASH high, RISET = 0.5 3.3V < VIN < 4.2V 2.8V < VOUT < 4.25V FLASH low, CTRL high, 2.8V < VOUT < 4.5V 3.0V < VIN < 4.5V
Min 460
Typ 500
Max 540
Units
Output Current
IOUT
mA 75 100 125
230
250
270 mV
ISET Reference Voltage
VISET
37.5
50
62.5
2005 Semtech Corp.
2
www.semtech.com
SC615
POWER MANAGEMENT Electrical Characteristics (Cont.)
Unless otherwise specified: TA = 25C for TYP, -40C to +60C for MIN and MAX; CBUCKET = COUT = 1.0F (ESR < 0.1); VIN = 3.0V to 5.25V; CIN = 10.0F; RISET = 0.5 (0.1%).
Parameter Quiescent Current
Symbol
Conditions FLASH high
Min
Typ 3.4 2.0 0.1
Max 5 4.5 2 500 1 1
Units mA mA A ms ms ms kHz
IQ
FLASH low, CTRL high FLASH low, CTRL low
Flash Mode Pulse Duration(1) Flash Mode Start-Up Time(1) Spotlight Mode Start-Up Time(1) Oscillator Frequency Oscillator Frequency Accuracy Short-Circuit Output Current Limit Input Current Limit
tFLASH tF-ST tS-ST fOSC fOSC ISC ILIMIT TOT
3.3V < VIN < 4.2V IOUT = 500mA, VOUT > 2.8V t = 0 when FLASH goes high to IOUT = 90% of final value t = 0 when CTRL goes high to IOUT = 90% of final value Device Enabled -15 VOUT = 0V VIN = 3.7V, VOUT = 4.0V 1.0 150 Hysteresis 10 1.5 250
15 465 2.1
% mA A C C V
Over-Temperature Protection
Logic Input High Threshold Logic Input Low Threshold Logic Input High Current Logic Input Low Current
VIH VIL IIH IIL V PP
FLASH, CTRL FLASH, CTRL FLASH, CTRL FLASH, CTRL Spotlight mode - IOUT = 100mA FLASH mode - IOUT = 500mA
0.4 1 20 0.1 25 35 2
V A A
ISET Ripple Voltage(1)
mV 100
Notes: (1) Guaranteed by design - not tested in production.
2005 Semtech Corp.
3
www.semtech.com
SC615
POWER MANAGEMENT Pin Configuration Ordering Information
DEVICE SC615IMLTRT (1)
VIN C2GND C1FLASH
1 2 3 4 5 T 10
PACKAGE MLPD-10 3x3
(2)
C2+ VOUT C1+ CTRL ISET
TOP VIEW
S C 615E V B
Evaluation Board
9 8 7 6
Notes: (1) Available in tape and reel only. A reel contains 3000 devices. (2) Available in lead-free package only. This product is fully WEEE and RoHS compliant.
MLP10: 3X3 10 LEAD
Pin Descriptions
Pin 1 2 3 4 5 6 7 8 9 10 T Pin Name VIN C 2GND C 1F LA S H ISET CTRL C 1+ VOUT C 2+ Thermal P ad Pin Function Input voltage. Negative terminal of bucket capacitor 2. Ground - connect to ground plane using multiple vias. Negative terminal of bucket capacitor 1. Flash mode enable pin - puts the device in active Flash mode when high and also overrides CTRL. Current-setting reference pin - connect to the LED cathode and the current setting resistor. Control input bit - used to enable and set the output current in Spotlight mode when high. Positive terminal of bucket capacitor 1. Output pin. Positive terminal of bucket capacitor 2 . Pad for heat sinking purposes -not connected internally. Connect to ground plane using multiple vias.
2005 Semtech Corp.
4
www.semtech.com
SC615
POWER MANAGEMENT Applications Information
Spotlight Mode Spotlight mode is enabled by setting the CTRL pin high and keeping the FLASH pin low. When in Spotlight mode, the SC615 can maintain a constant current indefinitely to drive an LED or bank of LEDs. The ISET reference voltage is set to 50mV so that the output current is mainIn Flash mode the SC615 output can drive 500mA at tained at 100mA when a 0.5 resistor is used. 4.25V into an LED for a minimum duration of 500ms. The FLASH pin is used to trigger this mode (active high). Protection Circuitry In spotlight mode the SC615 regulates the output cur- The SC615 also provides protection circuitry that prerent to 100mA when the CTRL pin is pulled high and the vents the device from operating in an unspecified state. FLASH pin is low. Note that Flash mode has priority over These funtions include Input Over-Voltage Protection Spotlight mode, i.e., the FLASH pin triggers Flash mode (IOVP), Output Over-Voltage Protection (OVP), Over-Temregardless of the state of the CTRL pin. perature (OT) Protection, Over-Current Protection (OCP), and Short-Circuit Current Protection (SCCP). Output current is regulated by attaching the ISET pin to the cathode(s) of the LED package and a low resistance Input Over-Voltage Protection sense resistor (typically 0.5). The ISET pin monitors Input over-voltage protection is included to prevent opthe voltage at the cathode and signals the charge pump eration at high input voltages that could damage the to increase or decrease the output current until the ISET device. The IOVP circuit senses the input voltage and voltage reaches the programmed setting. The resistor determines when the supply exceeds 6V. Hysteresis is value is chosen to set the current through the LED based included in this circuit to avoid chattering between states. on this reference voltage. The resistor can be chosen to When the voltage rises above this threshold, the device set either the flash mode current or spotlight mode cur- is disabled until the input voltage drops to a level within rent, but it should not be less than 0.5 due to output the specified range. current limitations of the device. Output Over-Voltage Protection Flash Mode Output over-voltage protection is included to prevent the Flash mode is enabled whenever the FLASH pin is pulled SC615 from generating an output voltage that could damhigh and remains active until the FLASH pin is released. age other devices connected to it such as load LEDs and This mode has higher priority than Spotlight mode, so bypass capacitors. When the output voltage exceeds the state of the CTRL pin is overridden whenever the 5.5V, the OVP circuit disables the charge pump until the FLASH pin is activated. While in flash mode the refer- voltage decreases to a level within the acceptable range. ence voltage on the ISET pin is set to 250mV. The duration of the pulse is limited by the amount of power that This circuit allows the device to drive LEDs with high forcan be dissipated in the SC615 before it exceeds the ward voltages at a reduced level without exceeding the maximum operating temperature. Note that if an output output voltage limits specified for the device. Note, howcurrent less than the rated 500mA is desired, the dura- ever, that this effect is a consequence of the OVP circuit tion of the pulse can increase proportionally. However, and is not its intended purpose. great care should be taken to insure the FLASH pin is not held high for an extended amount of time so that Over-Temperature Protection overheating does not occur. Extending flash mode be- The over-temperature circuit helps prevent the device yond the 500ms pulse limit could adversely affect the from overheating and experiencing a catastrophic faillong term reliability of the SC615. ure. When the junction temperature exceeds 150C the device is disabled. It remains disabled until the junction temperature drops below this threshold. As with the UVLO and OVP circuits, hysteresis is included to prevent toggling between modes.
2005 Semtech Corp. 5 www.semtech.com
General Operation The SC615 is a powerful 2X charge pump designed to drive a high-intensity white LED with a constant current (Spotlight mode) or with a pulsed current of higher intensity (Flash mode) used for camera flash.
SC615
POWER MANAGEMENT Applications Information (Cont.)
Over-Current Protection When the SC615 is in 2X charge pump mode, the input current will be approximately doubled the required output. When the steady-state load requires the maximum current available in 2X mode, the OCP circuit prevents the device from overheating due to excessive power dissipation. Short-Circuit Current Protection Short-circuit current protection is provided to limit the current that can be sourced when the output is shorted to ground. When a short circuit forces VOUT to drop below 2V, the SCCP detects the condition and limits the output current.
Resistor Selection The ISET resistor selection is critical in generating the correct current. The value can be chosen to set the Spotlight mode current or the Flash mode current, but it must be noted that the two current settings are dependent on the same resistor. It is recommended that the resistor be selected to match the desired LED current for Flash mode. This allows the designer to set the SC615's maximum current and select the package size necessary for the power dissipation required in Flash mode. The typical application shown on page 1, uses a 0.5 resistor to set a flash mode current of 500mA and spotlight mode current of 100mA. A high precision resistor should be used to ensure the specified accuracy for LED current. To avoid malfunction of the charge pump, it is recommended that the resistance seen at the ISET pin remain constant while the device is active (Flash or Spotlight mode). Changing the resistance value or the load current while the device is active could cause instability that would result in non-compliant behavior. The load current return path is from the ISET sense point through the resistor and back to the ground pins. Resistance in this path adds to the total resistance and has the effect of reducing the LED current by about 4% per 10mV of DC drop across the return copper trace in flash mode. For this reason, it is crucial to have a low resistance return path. Place and ground the resistor as close as possible to the ground pin of the SC615. The trace from the ISET pin has virtually no current. The ISET trace should make contact at the pad of the power sense resistor to minimize the effect of voltage drop between the LED cathode and the resistor. Capacitor Selection The SC615 is designed to use low-ESR ceramic capacitors for the input and output bypass capacitors as well as the charge pump bucket capacitors. Ideal performance is achieved when C1 is exactly equal to C2. It is recommended that X5R or X7R ceramic capacitors be used for best performance. Thermal Resistance The SC615 package is thermally efficient when the circuit board layout connects the thermal pad though multiple vias to the ground plane. The thermal resistance is rated at 49C/W and this rating is dependent on the connection between the thermal pad and the ground plane. A layout that is done correctly should keep the junction temperature below the OT limit while operating the SC615 within the specified electrical conditions for IOUT and VISET. A poor layout may allow the junction temperature to reach the OT limit while in Flash or Spotlight mode. So, it is important to maintain adequate ground plane around the device to maximize heat transfer to the PCB.
2005 Semtech Corp.
6
www.semtech.com
SC615
POWER MANAGEMENT Block Diagram
VIN
LDO
C1+
10F VBAT
250kHz C1C2+ CTRL Logic Control FLASH
1F
1F
CHARGE PUMP
C2VOUT white LED
CTRL
Reference Voltage Generator 1F
FLASH
GND
ISET
0.5
2005 Semtech Corp.
7
www.semtech.com
SC615
POWER MANAGEMENT Typical Characteristics
VOUT = 3.53V(start) to 3.40V(LED heated 500ms)
540
540
Flash Duration
Flash Current at 500ms
VOUT = 3.4V
LED Current [mA]
520
500
Current [mA]
100 200 300 400 500
VIN=4.2V VIN=3.75V VIN=3.3V
520
500
480
480
460 0
460 3.30
3.45
3.60
3.75
3.90
4.05
4.20
Pulse Duration [ms]
VIN [V]
Flash Current at 100ms
VOUT = 3.46V
540 540
Flash Current at 10ms
VOUT = 3.53V
520
520
Current [mA]
500
480
460 3.30
Current [mA]
500
480
3.45
3.60
3.75
3.90
4.05
4.20
460 3.30
3.45
3.60
3.75
3.90
4.05
4.20
VIN [V]
VIN [V]
100mA Spotlight Current VOUT = 2.93V
130.0
115.0
Current [mA]
100.0
85.0
70.0 3.00
3.45
3.90
4.35
4.80
5.25
VIN [V]
2005 Semtech Corp.
8
www.semtech.com
SC615
POWER MANAGEMENT Typical Characteristics (Cont.)
Startup Flash Mode 500mA Flash Mode VISET Ripple
Ch1 100mV/div Ch2 2V/div Ch3 2V/div 40us/div
Ch1 100mV/div Ch2 2V/div Ch3 2V/div 4us/div
2005 Semtech Corp.
9
www.semtech.com
SC615
POWER MANAGEMENT Layout Guidelines
The following layout is suggested for a two-layer design. The capacitors C1 and C2 are the bucket capacitors and each conducts the full load current of up to 500mA pulsed for one half clock cycle. C3 is the output decoupling capacitor placed near the SC615 VOUT pin. C4 is the input decoupling capacitor placed near the SC615 VIN pin. Multiple vias should be used whenever it is necessary to change layers on nets connecting to pins VIN, VOUT, GND, C1-, C1+, C2- and C2+. Resistor R1 is routed with a very low resistance connection between R1 and GND pin 3. The sense trace between Pin 6 and R1 is routed around the ground vias, allowing the shortest ground return path possible. The sense trace is connected to R1 at the positive terminal pad for the most accurate output possible. The bottom copper layer is mostly a ground plane with no obstructions between the ground vias. The smaller rectangle to the left connects the input power to VIN pin 1 and input capacitor C4. The two traces at the lower left are for logic inputs FLASH and CTRL. The trace to the right is the ISET pin "sense" trace. The sense trace is routed out of the path of the returning ground current.
Bottom Copper
Top Copper
2005 Semtech Corp.
10
www.semtech.com
SC615
POWER MANAGEMENT Outline Drawing -MLPD-10 3x3
A E B
DIMENSIONS INCHES MILLIMETERS DIM MIN NOM MAX MIN NOM MAX
A A1 A2 b C D E e L N aaa bbb .039 .031 .000 .002 (.008) .007 .009 .011 .074 .079 .083 .042 .048 .052 .114 .118 .122 .020 BSC .012 .016 .020 10 .003 .004 0.80 1.00 0.00 0.05 (0.20) 0.18 0.23 0.30 1.87 2.02 2.12 1.06 1.21 1.31 2.90 3.00 3.10 0.50 BSC 0.30 0.40 0.50 10 0.08 0.10
E PIN 1 INDICATOR (LASER MARK)
A aaa C C 1 LxN 2 A1 A2 C
SEATING PLANE
D
N e bxN bbb CAB
NOTES:
1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). 2. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS TERMINALS.
Marking Diagram
Top Mark
615 yyww xxxx
yyww = Datecode (Example = 0552) xxxx = Semtech Lot Number
2005 Semtech Corp.
11
www.semtech.com
SC615
POWER MANAGEMENT Land Pattern - MLPD-10 pin
K
DIM
(C) H G C G H K P X Y Z
DIMENSIONS INCHES MILLIMETERS
(.112) .075 .055 .087 .020 .012 .037 .150 (2.85) 1.90 1.40 2.20 0.50 0.30 0.95 3.80
Z
Y X P
NOTES: 1. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY. CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR COMPANY'S MANUFACTURING GUIDELINES ARE MET.
Contact Information
Semtech Corporation Power Management Products Division 200 Flynn Road, Camarillo, CA 93012 Phone: (805) 498-2111 FAX (805)498-3804 Visit us at: www.semtech.com
2005 Semtech Corp. 12 www.semtech.com

▲Up To Search▲

Price & Availability of SC615

	To Download SC615 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .